An anti-fog mesh or anti-fog heater is an electrical system that is installed in the mirror of the bathroom to prevent it from fogging. They are easy to install since it is a self-adhesive sheet that houses an electrical circuit inside. The power outlet can be removed from the line of light or from a socket. In case of an installation to the light current line, the mesh will start working when the bathroom or toilet light is turned on, and it will stop working when it is turned off. Although its power is electrical we are talking about a minimum consumption (60 W approximately). Have a look at the electric bathroom mirror info.
The anti-fog mesh is designed to prevent surface condensation in mirrors. It is an ideal product for bathrooms since they are a comfortable, safe and clean solution for those who want to avoid the condensation of the same and the constant marks that are produced because of it. It is a film so thin that it does not occupy any space and are highly resistant to dust, humidity and even shock.
The only requirement for installation is that this type of mesh must be attached directly to the moon on the back so that it cannot be installed properly if the mirror is mounted directly on a piece of furniture and you do not have access to the back of it. The fogging on the surfaces is caused by the phenomenon of condensation, which is when hot humid air meets a cold surface, being exact, with a temperature lower than that of condensation for that particular humidity. Knowing this, how can I avoid the fog in the bathroom mirror? For electric bathroom mirror info, there are only two possible solutions: either we reduce the absolute humidity of the room (amount of water suspended per unit of air) or we increase the temperature of the surface where we do not want the water vapour to condense.
Reducing humidity is relatively simple and this is one thing mentioned in electric bathroom mirror info, although doing it nicely is not so much. Open the bathroom door solves the problem, but of course, comes a cold nothing desired, so the option is to install an electric dehumidifier, which is neither cheap (between 100 and 200 euros what have the necessary power), or silent, neither comfortable nor energetically efficient, since they need to use a small compressor to cool a serpentine where the water condenses, which is collected in a bucket that we must empty periodically. In essence, it’s like a miniature air conditioner, only the hot air generated by the process stays in the room.
Bath mist – resistance
The other option, much smarter, is to heat the surface that we want free from fog, in this case, the mirror. Thus, placing a small resistance in the back of the mirror, we will achieve that in this area of the same not condense even a single drop of water. It is more or less the same system as in the rear moons of some cars, only with a higher density of the wiring for a faster effect. It uses a simple Anti-fog system and avoids the inconvenience of fogging your mirror in the bathroom.
If you are tired of the discomfort of the fog in your mirror when you finish showering or bathing and not being able to see yourself in the mirror, there is a novel antifog system to avoid all these problems. The anti-fog system consists of a device that provides heat to the back of the bathroom mirror, as a resistance, and that prevents the mirror from fogging. It is a very simple system that is effective and works by connecting it to the electricity grid.
Tip: Plug it into the bathroom light and you will not forget to unplug it. We could use an independent connection but we run the danger of forgetting it on.
Electric bathroom mirror info – why use it?
We highly recommend its use, as all are advantages:
Forget about opening the door or window of your bathroom to demist the mirror. Make it easy, and install an anti-fog system in your bathroom mirror. Normally it can be installed in any mirror; you only need a clean surface of the bathroom mirror from the back. Keep in mind that only the surface occupied by the anti-fog system plus a margin of around five centimetres will play. If the mirror is large, you can always combine several systems to demist more surfaces, but bear in mind, what is really important is that we demist the area of vision, which will be around a space of 40 × 40 centimetres.
This system has been proliferating over time, since formerly they were more complex systems and also had a high price, so it was considered a luxury product or only installed in hotels. But as you can see, all this has changed and it has become a very accessible product. It is a simple system, easily installed and in which all are advantages, so we can forget about opening the door or the bathroom window to demist the mirror. If still, we have not convinced you and you prefer to continue using traditional solutions to avoid fogging the mirror, we leave here a list of home remedies:
Its installation is much simpler since it is a very thin panel that is placed behind the mirror and can be connected to the same socket as the lamp that is usually placed on it. Its consumption is only 65W, little for the convenience of getting out of the shower and being able to shave (or put on makeup, as appropriate) seeing our reflection in the mirror.